Menu
Region:
TECH-MASTERS Group Changing region
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group
+43 7242 9396 1650
« ADHESIVES AND SEALANTS

Power Repair 21

POWER‐REPAIR 21 is a two‐part methacrylate
adhesive designed for structural bonding of
thermoplastic, metal and composite assemblies.
POWER‐REPAIR 21 is PVC- and silicone free.
POWER REPAIR 21 can be over-painted with most types of lacquers. Combined at a 1:1 ratio, it has a open time of 4 to 6 minutes and achieves 75% of ultimate strength in 10 to 20 minutes at room temperature (23°C).
POWER‐REPAIR 21 offers a combination of high strength and stiffness as well as the ability to bond a wide range of materials.

  • Excellent shear, peel and impact strength over a wide temperature range
  • Non sagging thixotropic formulation
  • Will fill gaps of up to 5 mm
  • Over paintable
  • Resistant to weathering and humidity
  • Room temperature cured with short open time
  • No surface preparation 100% reactive
  • Very good UV-resistance and excellent ageing properties
  • Isocyanate-, phthalates-, solvent-, PVC- and silicone free.
Article nr Name Content
T911200 Power Repair 21 creme 5 min. 50ml 50ml
T911205 Power Repair 21 black 5 min. 50ml 50ml
T911400 Power Repair 21 creme 5 min. 400ml 400ml
Y911302 Mixer Tip 50ml trans. 10pcs.
Y911303 Mixer Tip 50ml blue 10pcs.
Y911600 Reinforcement Tissue 12x360cm 1pc.
Y911601 Contouring Tissue 12x360cm 1pc.

» To the shop
  • Technical data
  • Application and usage
  • Downloads

ADHESIVE:
Aggregate State: Paste
Colour: yellow/black
Odour: characteristic
Flammability: Combustible
pH: 4,5 - 5,5
Initial boiling point and boiling range: 101 °C
Flash point: 10 °C
Upper/lower flammability or explosive limits: 2,1 - 12 Vol-%
Vapour pressure: 28 mm Hg (20 °C)
Vapour density: 3,5
Relative density: 0,96 (20 °C)
Dynamic viscosity: 55 Pa* s
Temperature resistance: -40°C – 125°C
Tensile strength: 24 Mpa
Open time: 4-6 min
Working time: 12-15 min
Curing time: approx. 20 min on 23°C
Complete curing: after 24 hours on 23°C

ACTIVATOR:
Aggregate State: Paste
Colour: whitish
Odour: characteristic
Flammability: Combustible
pH: 3,5 - 5,5
Initial boiling point and boiling range: 101 °C
Flash point: 10 °C
Upper/lower flammability or explosive limits: 2,1 - 12 Vol-%
Vapour pressure: 28 mm Hg (20 °C)
Vapour density: > 1
Relative density: 1,03 (20 °C)
Dynamic viscosity: 40000 - 60000 cP (25 °C)
UV- and weather resistance:  Excellent
Grit blasted steel to grit blasted steel -
100% strength retained.
Storage: All adhesives should be stored unopened in a cool, dry place (between 5°C and 25°C) when not used for a long period of time.
This product should never be frozen!

  • The surfaces to be bonded should be clean, dry and free from dust and grease.
    Application temperature: Between 15 °C and 25° C.
    In case of doubt of the substrate that must be bonded, test the strength on a small sample of the substrate.
  • Mixing:
    Mixing Ratio: 1:1
    Connect the mixertip to the cartridge and press out 2 cm (do not use) to be sure that you have a 100% mixture of the 2 components.
    PLEASE NOTE: Once the product cures in the nozzle it has to be thrown away and a new nozzle used.
  • Assembling:
    Open time 4 - 6 minutes @ 23°C.
    After applying the adhesive, assembly the parts (within open time) and immediately clamp or press.
    Movement of the part after the working time has expired can result in bond strengths lower than normal. Ensure that the assembly remains undisturbed until fixture has occurred.
  • Curing:
    Curing time: ca. 20 minutes @ 23°C.
    Complete curing:  24 hours @ 23°C. Temperatures higher or lower then 23°C will have influence on the open time and curing time.
    The viscosity’s of Parts A and B of this adhesive are affected by temperature.
pdf Product Information
techmasters_en_prp21_PDS.pdftechmasters_en_prp21_PDS.pdf (2.9 MB)
pdf MSDS T911200 Power Repair 21 creme 5 min. 50ml (Comp. B) V3
MSDS_T911200_Power_Repair_21_creme_5_min_50ml_Comp_B__T911200_V3_en_AT.pdfMSDS_T911200_Po...00_V3_en_AT.pdf (507.1 KB)
pdf MSDS T911205 Power Repair 21 black 5 min. 50ml (Comp. B) V3
MSDS_T911205_Power_Repair_21_black_5_min_50ml_Comp_B__T911205_V3_en_AT.pdfMSDS_T911205_Po...05_V3_en_AT.pdf (507.2 KB)
pdf MSDS T911205 Power Repair 21 black 5 min. 50ml (Comp. A) V3
MSDS_T911205_Power_Repair_21_black_5_min_50ml_Comp_A__T911205_V3_en_AT.pdfMSDS_T911205_Po...05_V3_en_AT.pdf (342.7 KB)
pdf MSDS T911200 Power Repair 21 creme 5 min. 50ml (Comp. A) V3
MSDS_T911200_Power_Repair_21_creme_5_min_50ml_Comp_A__T911200_V3_en_AT.pdfMSDS_T911200_Po...00_V3_en_AT.pdf (342.6 KB)

Power Repair 21

POWER‐REPAIR 21 is a two‐part methacrylate
adhesive designed for structural bonding of
thermoplastic, metal and composite assemblies.
POWER‐REPAIR 21 is PVC- and silicone free.
POWER REPAIR 21 can be over-painted with most types of lacquers. Combined at a 1:1 ratio, it has a open time of 4 to 6 minutes and achieves 75% of ultimate strength in 10 to 20 minutes at room temperature (23°C).
POWER‐REPAIR 21 offers a combination of high strength and stiffness as well as the ability to bond a wide range of materials.

  • Excellent shear, peel and impact strength over a wide temperature range
  • Non sagging thixotropic formulation
  • Will fill gaps of up to 5 mm
  • Over paintable
  • Resistant to weathering and humidity
  • Room temperature cured with short open time
  • No surface preparation 100% reactive
  • Very good UV-resistance and excellent ageing properties
  • Isocyanate-, phthalates-, solvent-, PVC- and silicone free.
Article nr Name Content
T911200 Power Repair 21 creme 5 min. 50ml 50ml
T911205 Power Repair 21 black 5 min. 50ml 50ml
T911400 Power Repair 21 creme 5 min. 400ml 400ml
Y911302 Mixer Tip 50ml trans. 10pcs.
Y911303 Mixer Tip 50ml blue 10pcs.
Y911600 Reinforcement Tissue 12x360cm 1pc.
Y911601 Contouring Tissue 12x360cm 1pc.

» To the shop
  • Technical data
  • Application and usage
  • Downloads

ADHESIVE:
Aggregate State: Paste
Colour: yellow/black
Odour: characteristic
Flammability: Combustible
pH: 4,5 - 5,5
Initial boiling point and boiling range: 101 °C
Flash point: 10 °C
Upper/lower flammability or explosive limits: 2,1 - 12 Vol-%
Vapour pressure: 28 mm Hg (20 °C)
Vapour density: 3,5
Relative density: 0,96 (20 °C)
Dynamic viscosity: 55 Pa* s
Temperature resistance: -40°C – 125°C
Tensile strength: 24 Mpa
Open time: 4-6 min
Working time: 12-15 min
Curing time: approx. 20 min on 23°C
Complete curing: after 24 hours on 23°C

ACTIVATOR:
Aggregate State: Paste
Colour: whitish
Odour: characteristic
Flammability: Combustible
pH: 3,5 - 5,5
Initial boiling point and boiling range: 101 °C
Flash point: 10 °C
Upper/lower flammability or explosive limits: 2,1 - 12 Vol-%
Vapour pressure: 28 mm Hg (20 °C)
Vapour density: > 1
Relative density: 1,03 (20 °C)
Dynamic viscosity: 40000 - 60000 cP (25 °C)
UV- and weather resistance:  Excellent
Grit blasted steel to grit blasted steel -
100% strength retained.
Storage: All adhesives should be stored unopened in a cool, dry place (between 5°C and 25°C) when not used for a long period of time.
This product should never be frozen!

  • The surfaces to be bonded should be clean, dry and free from dust and grease.
    Application temperature: Between 15 °C and 25° C.
    In case of doubt of the substrate that must be bonded, test the strength on a small sample of the substrate.
  • Mixing:
    Mixing Ratio: 1:1
    Connect the mixertip to the cartridge and press out 2 cm (do not use) to be sure that you have a 100% mixture of the 2 components.
    PLEASE NOTE: Once the product cures in the nozzle it has to be thrown away and a new nozzle used.
  • Assembling:
    Open time 4 - 6 minutes @ 23°C.
    After applying the adhesive, assembly the parts (within open time) and immediately clamp or press.
    Movement of the part after the working time has expired can result in bond strengths lower than normal. Ensure that the assembly remains undisturbed until fixture has occurred.
  • Curing:
    Curing time: ca. 20 minutes @ 23°C.
    Complete curing:  24 hours @ 23°C. Temperatures higher or lower then 23°C will have influence on the open time and curing time.
    The viscosity’s of Parts A and B of this adhesive are affected by temperature.
pdf Product Information
techmasters_en_prp21_PDS.pdftechmasters_en_prp21_PDS.pdf (2.9 MB)
pdf MSDS T911200 Power Repair 21 creme 5 min. 50ml (Comp. B) V3
MSDS_T911200_Power_Repair_21_creme_5_min_50ml_Comp_B__T911200_V3_en_AT.pdfMSDS_T911200_Po...00_V3_en_AT.pdf (507.1 KB)
pdf MSDS T911205 Power Repair 21 black 5 min. 50ml (Comp. B) V3
MSDS_T911205_Power_Repair_21_black_5_min_50ml_Comp_B__T911205_V3_en_AT.pdfMSDS_T911205_Po...05_V3_en_AT.pdf (507.2 KB)
pdf MSDS T911205 Power Repair 21 black 5 min. 50ml (Comp. A) V3
MSDS_T911205_Power_Repair_21_black_5_min_50ml_Comp_A__T911205_V3_en_AT.pdfMSDS_T911205_Po...05_V3_en_AT.pdf (342.7 KB)
pdf MSDS T911200 Power Repair 21 creme 5 min. 50ml (Comp. A) V3
MSDS_T911200_Power_Repair_21_creme_5_min_50ml_Comp_A__T911200_V3_en_AT.pdfMSDS_T911200_Po...00_V3_en_AT.pdf (342.6 KB)
1. Choose location
TECH-MASTERS Group
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group
2. Cookies

We use our own and third-party cookies to personalize content and advertisements, to be able to offer functions for social media and to analyze access to our website. The cookies are described in more detail under "Cookie Settings" and can be activated or deactivated. By clicking on "Allow all cookies" you agree to their use. You can subsequently change your cookie settings on the "Privacy Policy" page. Additional Information:  Privacy policy incl. cookie settings | General terms and conditions

Accept cookies

Cookie Settings

×
  • What are cookies?
  • Required Cookies
  • Performance Cookies
  • Marketing Cookies

What are cookies?

Cookies are text files that are stored by a browser on the end device to store certain information. With this information, our website recognizes that you have already visited it. We use this to prepare the information accordingly. Your personal data will not be saved.

Required Cookies

These cookies control functions without which our website cannot be used to its full extent. These cookies are only used by us (our own cookies). As a result, this information is only used and processed by our website. For example, you don't have to log in again every time you log in.

Performance Cookies

“Google Analytics” and “Google Tag Manager” are used to collect information on how our website is used. These cookies help us, for example, to determine whether and which sub-pages of our website are visited and what content the users are interested in. We primarily record the number of visits and their duration. Note on data processing in the USA: According to the case law of the European Court of Justice (judgement of July 16, 2020, case ref.: C-311/18 (“Schrems II”)) no adequate level of data protection exists in the USA. In addition, government surveillance measures in the USA may result where no adequate legal protection can be sought against these measures. In particular, US security and secret services may have access to your data without you being informed and without you being able to take legal action against it. The data processing in the USA in connection with the data processed by Tech-Masters Trading GmbH is based on your consent in the sense of Art. 49 para. 1 lit a) in conjunction with Art. 6 para. 1 lit a) GDPR. You can revoke your consent at any time non-retroactively. Understanding the above information on data protection in the USA, I also consent to the processing of personal data in the USA if and to the extent that I give my consent to the use of cookies via configuration of the cookie settings. I may revoke my consent at any time non-retroactively.

Marketing Cookies

We show "Youtube" videos for some products. This marketing cookie comes from Google and collects information about the websites visited by the user in order to create targeted advertising for the visitor. In this context, we do not process any personal data without your consent in accordance with Article 6 (1) (a) GDPR.